{"product_id":"cold-air-intake-kit-for-1997-2003-ford-f-150-expedition-v8-engine","title":"Flashark Cold Air Intake for 1997-2003 Ford F-150 \/ 1997-2002 Expedition 4.6L\/5.4L (V8 Engine)","description":"\u003ch3\u003eFlashark 3.5\" Cold Air Intake for 1997–2003 Ford F-150 \/ 1997–2002 Ford Expedition — 4.6L \u0026amp; 5.4L Triton V8\u003c\/h3\u003e\n\u003cp\u003eYour Triton V8 was built to work. Whether you're towing a trailer, hauling lumber, or just daily-driving an old reliable Ford, the factory intake is holding it back. That plastic snorkel and restrictive paper filter were designed for noise compliance, not for the 4.6L or 5.4L Triton to breathe.\u003c\/p\u003e\n\u003cp\u003eFlashark's 3.5\" cold air intake replaces the factory plumbing with a mandrel-bent 89mm aluminum tube — black powder-coated for a clean, factory-like look that won't show dirt after a decade of use. The dual steel heat shields isolate the filter from the engine bay, pulling cooler air from the fender well. Intake temps drop 15–25°F, which on a naturally aspirated V8 means more consistent throttle response and improved low-RPM torque — right where you tow and haul.\u003c\/p\u003e\n\u003cp\u003eThe dry, reusable cone filter needs no oil. Clean it with soap and water, let it dry, and reinstall. No MAF contamination, no check engine light, no idle hunting. The CNC-machined MAF housing is calibrated to match the factory Triton ECU, so your truck runs exactly as Ford intended — just with more airflow and a deeper V8 growl under throttle.\u003c\/p\u003e\n\u003cp\u003eInstallation is about 60 minutes with basic hand tools. Every bracket, coupler, breather hose, and clamp is in the box.\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e3.5\" (89mm) mandrel-bent aluminum intake tube\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— black powder-coated finish, smooth interior walls; maximizes airflow for both 4.6L and 5.4L Triton V8 engines\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDry high-flow cone filter (red)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— washable, reusable, no oil required; won't foul your MAF sensor; clean every 15,000–20,000 miles\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual steel heat shields\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— two-piece design isolates filter from engine bay heat; routes intake to fender-well cold air; 15–25°F intake temp reduction\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrecision MAF calibration\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— CNC-machined 89mm housing delivers clean laminar airflow; no CEL, no idle surging, no hesitation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo breather hoses included\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— φ16×700mm and φ16×800mm, direct-fit for Triton PCV routing; no parts store runs needed\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStraight + reducer silicone couplers\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— multi-layer black silicone with stainless T-bolt clamps; leak-free seal under load\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo tune required\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— plug-and-play with factory ECU; 4.6L and 5.4L Triton PCM adapts fuel trims automatically\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBolt-on installation\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— factory mounting points, no cutting or drilling; ~60 minutes \u003cstrong\u003ewith basic hand tools\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003cstrong\u003ePackage Includes\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1× 3.5\" mandrel-bent aluminum intake tube (black powder-coated)\u003c\/li\u003e\n\u003cli\u003e1× Dry high-flow cone air filter (red, washable \u0026amp; reusable)\u003c\/li\u003e\n\u003cli\u003e2× Steel heat shields (dual-plate design)\u003c\/li\u003e\n\u003cli\u003e1× Straight silicone coupler (φ82–89mm)\u003c\/li\u003e\n\u003cli\u003e1× Reducer silicone coupler (φ82–89mm)\u003c\/li\u003e\n\u003cli\u003e2× Breather hoses (φ16×700mm + φ16×800mm)\u003c\/li\u003e\n\u003cli\u003e1× Tube plug (10mm inner diameter)\u003c\/li\u003e\n\u003cli\u003e4× Narrow band clamps + stainless T-bolt clamps\u003c\/li\u003e\n\u003cli\u003e1× Installation hardware kit (all brackets, bolts, nuts, and washers)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Flashark","offers":[{"title":"Default Title","offer_id":51797412872478,"sku":"FLIS25126","price":95.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0679\/7171\/1262\/files\/Cold-Air-Intake-Kit-for-1997-2003-Ford-F-150-Expedition-_V8-Engine_-Flashark-102909198_aadc71d3-5cf3-4873-b467-c3e5773f2ad3.jpg?v=1782569195","url":"https:\/\/platinumhpsolutions.com\/products\/cold-air-intake-kit-for-1997-2003-ford-f-150-expedition-v8-engine","provider":"Platinum High Performance Solutions, LLC.","version":"1.0","type":"link"}